Bullet Sensors & Transducers e-Digest, Vol. 148, Issue 1, January 2012: Products News

    (ISSN 1726-5479)

 

 

Editorial Calendar 2013

Editorial Board

Submit an Article

Submit a White Paper

Submit Press Release

Best Selling Articles 2012

Top 25 Downloaded Article

10 Top Sensors Products of 2012

Best_Articles_2011

Sensors & Transducers Journal 2011

Journal Subscription

iC Haus logo

 

 

Submit Press Release

 

or / and

 

White Paper

2000-2002 S&T e-Digest Contents

2003 S&T e-Digest Contents

2004 S&T e-Digest Contents

2005 S&T e-Digest Contents

2006 S&T e-Digest Contents

2007 S&T e-Digest Contents

2008 S&T e-Digest Contents

2009 S&T e-Digest Contents

2010 S&T e-Digest Contents

2011 S&T e-Digest Contents


 

 

Universal Sensor Interface for Flow, Gas, and Pressure Sensors

 

 

The new iC-HO device is a universal sensor interface for the assembly of flow, gas, and pressure sensors. The following functional units are included in the device: a configurable signal conditioner, a fast analog/digital converter, configurable current sources, temperature drift compensation, digital sensor configuration, an SPI C interface, adjustable linearization, and a ratiometric, differential analog output. All of these functions are housed on a monolithic chip in a QFN32 package measuring 5 mm x 5 mm.

 

Resistive mass airflow sensors are driven by iC-HO using two identical reference currents so that the voltage difference conditioned by the programmable amplifier (PGA) can be measured and processed in a digitized form. The necessary temperature control unit is fully integrated in the chip.

 

With gas sensors a variable tracking controller for two temperatures with a configurable temporal sequence is used. Differential, synchronous recording of the sensor resistance can be configured. The heating controller monitors the sensor temperature according to the profile using the energized heating resistor. It is not necessary to electrically split the heating resistor and sensor resistor on a sensor MEMS element as iC-HO electrically separates the heating and measurement units.

 

With pressure sensors, for example, iC-HO provides differential measurement on a resistor measuring bridge as a half or full bridge. By performing an additional measurement the sensor temperature curve can be suitably compensated for. It is also possible to supply the measuring bridge using a constant current source in place of a voltage.

 

For flow and gas sensor applications a heating system with a control circuit is also required in addition to the sensor conditioning unit. An on-chip heating controller drives a sensor heating resistor through additional differential sensor inputs and a digital PI controller with D/A conversion. The PI controller can exercise both relative and absolute control over the temperature. A maximum heating current can be specified to protect the external MEMS sensors.

 

Gain and offset correction of the programmable amplifier (PGA) can be automatically tracked for the purpose of sensor temperature compensation. The fast, 11-bit A/D converter can either process the measurement values directly or as the difference between two conversions.

 

The measurement values are output through a ratiometric, differential analog output. Alternatively, the SPI interface implemented for chip configuration can be used to scan the measurement value and system state through a microcontroller.

 

Error states and error thresholds can be defined to monitor and diagnose the sensor and chip. These are output through an open collector switching output or the SPI interface.

 

iC-HO has an internal reference voltage and can output internal analog signals and the bias current to standard signal pins for calibration.

 

iC-HO operates from 4.5 V to 5.5 V within a temperature range of -25C to +104 C. At just 5 mm x 5 mm x 1 mm the 32-pin QFN package is extremely compact and has a very good heat dissipation.

 

The design-in process is supported by ready-to-operate demo boards and software for evaluation with a PC.

 

 

About iC-Haus

 

iC-Haus GmbH is a leading independent German manufacturer of standard iCs (ASSP) and customized ASiC semiconductor solutions. The company has been active in the design, production, and sales of application-specific iCs for industrial, automotive, and medical technology for over 25 years and is represented worldwide. The iC-Haus cell libraries in CMOS, bipolar, and BCD technologies are fully equipped to realize the design of sensor, laser/opto, and actuator ASiCs, among others. The iCs are assembled in standard plastic packages or using iC-Haus chip-on-board technology to manufacture complete microsystems, multichip modules, and optoBGATM, the latter in conjunction with sensors. Further information is available at http://www.ichaus.com

 

 

Contact:

 

Marko Hepp

iC-Haus GmbH,

Am Kuemmerling 18,

55294 Bodenheim, Germany

Tel.: +49 6135 9292 302

Fax: +49 6135 9292 192

E-mail: marko.hepp@ichaus.de

Web: http://www.ichaus.com

iC-HO universal sensor interface

Sensors Web Portal's logo

 

 

 

Digital Sensors and Sensor Sysstems

 

SENSORCOMM' 2013 banner

 

 

 

Read more about Universal Sensors Interfaces

 

 

Handbook of Laboratory Measurements

 

 

Back to S&T e-Digest page

 


1999 - 2013 Copyright , International Frequency Sensor Association (IFSA). All Rights Reserved.