Bullet Sensors & Transducers e-Digest, Vol. 93, Issue 6, June 2008: Product News

    (ISSN 1726- 5479)

 

Editorial Calendar 2007

Editorial Board

Submit an Article or Press Release

10 Top Sensors Products of 2007

Sensors & Transducers Journal 2007

Journal Subscription 2008

Analog Devices logo

Top 25 Downloaded Article

2000-2002 S&T e-Digest Contents

2003 S&T e-Digest Contents

2004 S&T e-Digest Contents

2005 S&T e-Digest Contents

2006 S&T e-Digest Contents


 

 

Inertial Sensor Reduces Cost and Complexity of Industrial Motion Control Designs

 

 

Norwood, MA(6/9/2008) - is expanding its iSensor™ intelligent sensor product family with a new six-degrees-of-freedom (6 DoF) inertial sensor. The ADIS16365 IMU (inertial measurement unit) combines high-performance, simplicity, and an improved data interface that delivers faster response times and lowers power consumption relative to other IMUs in its class. The ADIS16365 makes complex motion sensing design significantly easier and more cost-effective for industrial engineers developing high-performance platform control and navigation equipment. The new IMU reduces power consumption by at least 20 percent, boasts an approximate 10 times improvement in start-up time and improves bias stability by up to 50 percent, lowering noise sensitivities that impede navigation accuracy. In addition to traditional industrial vehicle navigation systems, the ADIS16365’s low noise and fast response time also benefit a wide range of platform stability applications, such as vehicle mounted antennas and cameras.

 

 

Improved GPS Navigation

 

The ADIS16365 can be used anywhere high-performance motion control and feedback is required. In vehicles that rely on GPS satellite navigation to maintain accurate position information, such as high-end agricultural equipment, the IMU enhances their performance by immediately detecting small shifts in the position of the GPS antenna due to rough terrain. This allows for real-time signal correction and provides the highest degree of heading accuracy. Additionally, a vehicle-mounted camera or a factory automation robotic arm can rely on the ADIS16365’s fast response time and excellent stability to maintain ultra-fine resolution even under erratic conditions.

 

“Most inertial motion sensors available today offer a low level of integration and require a high degree of factory calibration,” said Andy Garner, product line director for iSensor intelligent sensor products, Analog Devices. “The ADIS16365 comes fully calibrated and compensated for temperature, voltage and other sensitivities. This means customers receive meaningful data from the device immediately, without requiring additional motion testing or system integration. With its improved stability and feature-rich interface, the ADIS16365 significantly reduces the cost, time and risk of implementation for our customers. The new IMU fills the considerable void between large, expensive IMUs and less integrated sensors that leave much of the design testing and cost burden to the customer.”

 

 

ADIS16365 Provides Superior, Accessible and Affordable Performance

 

IMU sensor implementation involves complex electro-mechanical design, including many sensor-to-sensor and environmental interdependencies. Traditional solutions are more expensive and also highly customized to a narrow class of applications. The factory calibrated and programmable ADIS16365 simplifies the process of implementing full IMU sensor capability, and provides affordable, precision 6 DoF sensing to the broadest range of customers and applications. The device includes several unique features that further reduce design time and complexity, including an automatic sensor point-of-reference realignment, digital range scaling, dynamic environmental compensation, autonomous self test, and embedded sensor condition monitoring. The device leverages Analog Devices’ proprietary motion and calibration testing processes to capture sensor data and alignment compensations across all three axes, which are then embedded within the IMU, along with calibration for voltage variances, temperature variances, and other influences, all of which are then dynamically compensated in-use and are transparent to the user.

ADIS16365 inertial measurement unit

Sensors web portal

 

 

Harnessing ADI’s MEMS Expertise for Six-Degrees-of-Freedom Motion

 

Designed using Analog Devices’ world-class iMEMS® Motion Signal Processing Technology™, the ADIS16365 IMU combines three gyroscopes and three accelerometers to provide 6 DoF motion sensing. With the aid of embedded features such as the Precision AutoNull, and an outstanding 0.05o/sec/g dynamic linear acceleration compensation factor, equipment designers can achieve in-run bias stability of 0.009o/sec or better without having to perform further motion testing. For industrial applications, the ADIS16365 achieves unprecedented performance levels and significantly reduces post-processing complexity and implementation cost for the system designer. The new IMU sensor includes a programmable SPI (serial peripheral interface) port that provides easy access to device features, such as digital filtering, sample-rate, power-management, self-test, and sensor condition status and alarms. The sensor, smaller than a 1-inch cube, is footprint-compatible with previous generations. With only power supply and SPI connections, the device is fully in-system tunable, allowing designers to quickly and easily debug their system and experiment with different configurations for design optimization.

 

 

Contact:

 

Linda Kincaid

Analog Devices, Inc.

One Technology Way

P.O. Box 9106, Norwood, MA, 02062-9106 USA

Tel.: 781-937-1472

E-mail: linda.kincaid@analog.com

 

 

 

Back to S&T e-Digest page

 


1999 - 2008 Copyright ©, International Frequency Sensor Association (IFSA). All Rights Reserved.